Skip to content
مورد مصر MAWRED EGYPT
Upright carpet vacuum with brush roll

SKU VC-05

Upright carpet vacuum with brush roll

An upright carpet vacuum is pushed ahead of the operator like a small cart, with a rotating brush in its head that stirs the carpet pile and lifts out the sand and grit lodged deep in it for the suction to carry away. It suits hotel corridors, conference halls, mosques and offices with wall-to-wall carpet over continuous areas.

Updated

SKU
VC-05
Category
Wet and dry vacuum cleaners
Request a quote

We reply with a written quote after reviewing your request.

Suitable for: Hotel cleaning supplies، Office cleaning supplies، Cleaning supplies for clubs and gyms

Not suitable for: Not for tile, marble or wood floors unless the brush can be switched off, nor for hand-made rugs with fringes. It does not pick up liquids and will not go under low furniture.

Specifications

OperationPushed forward, brush roll with dry suction
BrushBristle roller driven by a belt or its own motor, depending on the model
Dust collectionBag in a front housing
Height adjustmentManual or automatic, to suit the pile depth
Side hoseShort hose for edges and corners on most models
Cleaning width and powerBy model, confirmed in the quote
SKUVC-05

Sand is what really wears carpet out

Stains do not destroy carpet. Grains of sand do: they sink to the base of the pile and act like sandpaper under every footstep. In dusty cities they arrive on shoes every day. Suction alone takes what lies on the surface and leaves what has settled deep down, which is why walking lanes fade before the rest of the carpet. A brush roll taps the pile lightly and repeatedly, working the grains up to where the airflow catches them.

What sets it apart in long corridors

The operator walks behind the machine in a straight line, without bending and without the back-and-forth arm movement a hose demands. Along a hotel corridor or across a conference hall, that shows in how fast the work goes and in how the operator feels at the end of the shift. The brush also leaves the pile standing in one direction, so the carpet looks groomed after each pass, a finish hotels care about outside guest rooms.

Setting the brush height

A brush set too low makes the machine heavy to push, wears the pile and strains the belt. Set too high, it does not touch the carpet and cleans nothing. The right setting has the bristles just meeting the top of the pile. Reset it when moving from short office carpet to thick carpet in a hall or suite. Some models do this by themselves.

Looking after the brush and belt

Threads and hair wind around the roller over time and stop it turning, so cut them away at least once a week. The rubber belt stretches with use and is replaced when the brush loses drive, so keeping a spare is sensible. The brush itself is replaced once its bristles have worn short. Pull the plug before any of this.

Where it sits in carpet care

An upright is for daily dry cleaning and does not replace washing. Periodic washing with shampoo and a spray-extraction machine removes bonded soil and stains, while good daily vacuuming delays the need for it and improves the result. Edges along the wall and the space under furniture still need the side hose or a small dry vacuum.

Useful points for the quote request

Give the approximate carpet area and its type, short pile or thick, and whether it is mostly long corridors or small rooms full of furniture. Say whether there are hard floors you want to clean with the same machine, how many units you need, and whether spare bags, belts and brushes should be included.

Alternatives

Frequently asked questions

Does an upright vacuum replace carpet washing?
No. It removes dry soil daily, while soil bonded to the pile and stains come out with periodic washing. Regular vacuuming lengthens the time between washes.
Can it be used on mosque prayer carpet?
Yes when the carpet is fitted to the floor. Loose-laid rugs get pulled in at the edges by the brush and are better cleaned with a plain suction nozzle.
Why has the brush stopped turning while the motor still runs?
The usual cause is a broken or slack belt, or threads wound around the roller. Unplug the machine and check both before calling for service.
Request a quote

Need a quote for your facility?

Send your list of items and quantities and we reply with a written quote.