Stainless 201 vs 304 for waste bins
Grade 304 stainless steel contains more nickel than 201, so it resists rust and staining in wet places such as washrooms, kitchens, hospitals and buildings near the sea. Grade 201 replaces part of the nickel with manganese and has slightly less chromium, so it suits dry offices and corridors. Where there is water or daily chlorine cleaning, choose 304 and ask for the grade in writing in the quote.
Written by Mawred Egypt technical team, Procurement and product team at Mawred Egypt
Published · Updated
What separates 201 from 304 in the metal itself?
Stainless steel is not one material but a family of iron alloys that contain chromium. Chromium forms a very thin layer on the surface that protects it from rust, and when that layer is scratched it re-forms by itself in contact with air. That is why stainless steel lasts.
Grade 304 is the most widely used grade in kitchen equipment, hospital fittings and washroom accessories, and it contains more chromium and nickel. Nickel makes the alloy more stable and better able to resist moisture and cleaning chemicals. Grade 201 was developed to reduce the use of nickel, replacing a large part of it with manganese and nitrogen, and it usually has slightly less chromium too. The result is an alloy that is stronger and harder to form, but less resistant to rust.
| Point of comparison | Stainless 201 | Stainless 304 |
|---|---|---|
| Nickel | Lower, partly replaced by manganese | Higher |
| Chromium | Slightly lower | Higher |
| Resistance to rust and staining | Moderate, good in dry conditions | High, suits damp and daily cleaning |
| Tolerance of chlorine and strong cleaners | Poor if left on the surface | Better, though rinsing afterwards is still needed |
| Suitable places | Offices, dry corridors, covered lobbies | Washrooms, kitchens, hospitals, buildings near the sea |
| Response to a magnet | Usually not attracted, or only slightly | Usually not attracted, or only slightly |
When does the difference show?
You cannot tell the two grades apart by eye when buying. They have the same shine and the same brushed finish. The difference shows after months in a damp location: brown spots may start to appear on a 201 bin in a busy washroom, especially at the base and around the pedal where water collects. The same bin in a dry air-conditioned corridor may go years without a problem.
So the choice starts with one question: where will this bin stand?
When to choose 304
Choose 304 in these cases:
- Washrooms and ablution areas, because water, soap and humidity are there all the time.
- Kitchens and pantries, because food waste contains water, salts and acids.
- Hospitals and clinics, because daily disinfection with chlorine and other disinfectants attacks the surface.
- Buildings in coastal cities or near the sea, because the air carries salt.
- Entrances and car parks open to the rain.
The same reasoning applies to other washroom fittings such as soap dispensers, tissue holders and stainless hand dryers, which work in the same damp conditions.
When 201 is enough
In administrative offices, air-conditioned corridors, meeting rooms and covered lobbies in a city away from the sea, 201 does the job well. What matters is that the space stays dry and is cleaned with a mild detergent, not concentrated chlorine. If a building has both kinds of space, split the order: 304 for washrooms and the kitchen, 201 for offices and corridors.
How to specify the grade in a quote
The only thing that really protects you is having the grade in writing. In your quote request, write the grade you need beside each item, for example "pedal bin, 30 litres, stainless 304". Ask the supplier to repeat it in the same form on the quote and then on the invoice. If an offer only says "stainless" with no grade number, ask before you accept.
For a large quantity, ask for a sample to inspect and leave in place for a while before taking the full order. That gives you a chance to judge the build quality, the finish and the pedal as well as the material.
Does the magnet test work?
Many buyers hold a magnet to the bin and assume that if it does not stick, the metal is 304. That is wrong. Grades 201 and 304 belong to the same family and in their original state are usually not attracted to a magnet. Both may pull slightly at bends, edges and welds, because forming changes the structure of the metal at those points.
What a magnet does reveal is the nickel-free types, which attract it clearly. So if a magnet sticks firmly to the body of the bin, the metal is probably neither 201 nor 304. If it does not stick, that proves nothing. Real confirmation needs a metal analyser or a dedicated test solution, which most buyers do not have, so the grade written on the quote remains the basis.
Making stainless last, whatever the grade
Wipe along the brushed grain with a soft cloth. Avoid steel wool and wire brushes, since they scratch the protective layer and leave iron particles on the surface that rust, so the bin looks as if it has rusted itself. If you use chlorine or a strong disinfectant, rinse with clean water and dry the surface straight away. If light marks appear early on, an ordinary stainless steel cleaner usually removes them before they set in.